How to Install a Gooseneck Faucet

Installing a gooseneck faucet can bring a new life to your kitchen. With its increased height and reach, it can provide better functionality and style to your sink. Gooseneck faucets are also known as high-arc faucets or high-neck faucets.

They have a curved spout that resembles a goose’s neck, hence the name. These faucets are becoming increasingly popular in modern kitchen designs.

If you’ve decided to replace your old faucet with a new gooseneck faucet, this article will guide you on how to install a gooseneck faucet step-by-step.

Materials Needed

Before starting the installation process, you will need some materials to complete the installation. Here’s a list of the materials you need:

– Gooseneck faucet
– Adjustable wrench
– Basin wrench
– Plumbers tape
– Silicone caulk
– Bucket or container

Step-by-Step Guide on How to Install a Gooseneck Faucet

The installation process can vary depending on the type of gooseneck faucet you want to install. Still, the general principles are generally the same. Here’s a step-by-step guide on how to install a gooseneck faucet:

Step 1: Turn Off the Water Supply

The first task before starting the installation process is to turn off the water supply to the sink. Usually, the water supply valves are located under the sink. Turn off both the hot and cold water valves.

Step 2: Remove the Old Faucet

After shutting off the water supply, you can now remove the old faucet. Use an adjustable wrench to disconnect the water supply lines from the old faucet. You should also use pliers to remove the mounting nuts that hold the old faucet in place. Some faucets may have mounting brackets that require a basin wrench to remove them.

Before removing the old faucet, ensure that the water supply lines are draining into a container or bucket to avoid dripping water on the floor. Once you’ve removed the old faucet, you should also clean the sink’s surface where the old faucet was mounted.

Step 3: Prepare the New Faucet

Carefully unpack the components of the faucet and ensure that you have all the necessary parts for the installation process. You should also inspect the faucet to ensure that all the parts are in good condition and free of defect.

Step 4: Install the Base Plate

If your new faucet comes with a base plate, you can now install it. The base plate covers the holes in the sink, enabling you to secure your faucet to the sink. Place the base plate over the mounting holes on the sink and align it to ensure it sits flat on the sink surface. Once you have the base plate correctly positioned, use the mounting hardware provided with the faucet to secure it in place under the sink.

Step 5: Connect the Water Supply Lines

After successfully mounting the base plate, connect the water supply lines to the new faucet. Start by wrapping the threads of the faucet’s tailpiece with Teflon tape to ensure a secure connection. You should then connect the water supply lines to the corresponding sides of the faucet’s tailpiece. Tighten the connections using pliers to create a secure and tight seal.

Step 6: Install the Faucet

Install the faucet onto the sink by positioning it into the mounting holes at the center of the base plate. Ensure the faucet is level and aligned correctly with the sink. Hand-tighten the mounting nuts until the faucet is stable. You can use an adjustable wrench to tighten any loose nuts.

Step 7: Check for Leaks

Once you’ve installed the faucet, turn the water supply valves back on to check for leaks. Allow the water to run for a while before checking for any drips under the sink. If you notice any leaks, turn off the water supply, and recheck the connections. Tighten any loose connections with pliers and ensure that all the connections are secure.

Step 8: Caulk Around the Base Plate

The final step is to apply some silicone caulk around the edges of the base plate. This will create a watertight seal to prevent any leaks that may occur around the mounting holes. Apply a bead of silicone caulk around the baseplate and smooth it out with a caulk gun or your finger.

How do you Tighten a Gooseneck Faucet Handle?

1. First, locate the set screw or handle screw that secures the handle to the faucet. This is usually located on the underside of the handle, near the base.
2. Using an Allen wrench or screwdriver, turn the set screw or handle screw clockwise to tighten it. Be careful not to overtighten, as this can damage the handle or the faucet.
3. Once the screw is tightened, test the handle to make sure it is secure. If the handle still feels loose, you may need to tighten the screw further or consider removing the handle to check for any worn or damaged parts.
4. To remove the handle, first turn off the water supply to the faucet. Then, use a flathead screwdriver or other tool to pry off the decorative cap or cover that sits on top of the handle.
5. Underneath the cap, you should see a retaining screw that holds the handle in place. Use an appropriate tool to remove this screw.
6. Once the screw is removed, you should be able to lift the handle off of the faucet. Check for any worn or damaged parts that may need to be replaced.
7. If everything looks good, reattach the handle by placing it back onto the faucet and securing it with the retaining screw. Replace the decorative cap or cover and turn the water supply back on.
8. Test the handle again to make sure it is secure and working properly. If you continue to experience issues, it is recommended to consult a professional plumber for assistance.

Conclusion

Installing a gooseneck faucet is relatively straightforward and can be done by anyone with basic plumbing knowledge. You only need to follow the steps provided in this guide to achieve a successful installation. Before purchasing a gooseneck faucet, ensure that it’s compatible with your sink and meets your kitchen needs. Once installed, you’ll enjoy the numerous benefits of a gooseneck faucet, including functionality and style.

FAQ

What is the purpose of gooseneck faucet?

A gooseneck faucet is designed to provide a higher clearance above the sink, allowing for larger items such as pots and pans to be easily filled and washed. The curved shape of the spout also adds an elegant and modern look to the kitchen.

What is the flow rate of a gooseneck faucet?

The flow rate of a gooseneck faucet is not fixed and can differ based on the specific model and brand. The flow rate of some gooseneck faucets can be as low as 0.5 gallons per minute (gpm), while others may have a higher flow rate of 4.65 gpm or 2.2 gpm.

What type of kitchen faucet is gooseneck?

A gooseneck faucet is a type of kitchen faucet that features a tall, curved spout that resembles the neck of a goose. It is commonly used in modern kitchens for its practicality and aesthetic appeal.

What is also known as gooseneck pipe?

A gooseneck pipe is also known as a swan neck or a serpentine pipe. It refers to a pipe that has a curved or bent shape, similar to the neck of a goose.

What are goosenecks made out of?

Goosenecks can be made out of a variety of materials, including stainless steel, brass, chrome, and nickel. The material used will depend on the specific model and brand of the faucet.

Which pipe is used for making gooseneck in the house connection?

The pipe used for making a gooseneck in a house connection is typically a flexible metal or plastic pipe, such as PEX or PVC. These materials are able to bend and curve without kinking or breaking, allowing for the creation of a gooseneck shape.