How to Remove American Standard Kitchen Faucet?

Are you tired of your leaky American Standard kitchen faucet? Don’t worry! With a little bit of knowledge and some tools, you can easily remove and replace your faucet.

In this article, we’ll go through all the steps required to remove an American Standard kitchen faucet. Let’s get started,

Tools Needed

• Basin wrench
• Adjustable wrench
• Allen wrench
• Channel-lock pliers
• Masking tape
• Flathead screwdriver

American Standard kitchen faucet Removal Instructions

Turn off the water supply

Locate the shut-off valves under the sink and turn them clockwise to shut off the water supply to the faucet. If you can’t find shut-off valves for the faucet, you may need to shut off the main water supply to your home.

Disconnect the supply lines

Use an adjustable wrench or pliers to disconnect the supply lines that are connected to the faucet. There will typically be two supply lines, one for hot water and one for cold water, connected to the bottom of the faucet.

Remove the mounting nuts

Locate the mounting nuts that secure the faucet to the countertop or sink. These are usually located underneath the sink. Use a wrench or pliers to loosen and remove the mounting nuts.

Remove the faucet handle

Depending on the type of American Standard faucet you have, you may need to remove the handle before you can fully remove the faucet.

This can usually be done by locating a screw on the underside of the handle or by prying off a cap and using a screwdriver to remove the screw.

Lift the faucet off the sink or countertop.

Once the mounting nuts and handle (if applicable) are removed, carefully lift the faucet off the sink or countertop.

If the faucet seems stuck, you may need to gently wiggle it back and forth while lifting it to release it.

Clean the area

After removing the faucet, clean the area on the sink or countertop where the faucet was installed. Use a mild cleaner or vinegar to remove any residue or stains.

How to Remove an American standard kitchen faucet with no set screw or cap?

Step 1: Inspect the faucet handle closely to see if there is a cover plug or cap that needs to be removed. Look for a small indentation or slot on the handle that may indicate the presence of a hidden cap.

Step 2: If a cover plug is present, use a small screwdriver or a similar tool to carefully pry it out. Be gentle to avoid damaging the handle or surrounding area.

Step 3: Once the cover plug is removed, you may be able to see a screw underneath. Use a screwdriver to turn the screw counterclockwise to loosen and remove it.

Step 4: If there is no set screw visible even after removing the cover plug, you can try grasping the handle firmly with one hand while using your other hand to gently turn the base of the handle counterclockwise direction. Apply steady but gentle pressure to see if the handle comes loose.

Step 5: If the handle still doesn’t come off, you may need to use a wrench to unscrew the cap or retaining nut that is securing the handle. Use an adjustable wrench or pliers to turn the cap or nut counterclockwise to loosen and remove it. Be careful not to apply too much force or use tools that may scratch or damage the handle.

Step 6: Once the cap or retaining nut is removed, you should be able to lift off the faucet handle from the base.

Step 7: Clean the area where the handle was removed and inspect for any worn or damaged components that may need to be replaced.

Additional details and tips

1. If the handle is still stuck even after trying the above steps, you can try using a lubricant such as WD-40 to help loosen it. Apply the lubricant and let it sit for a few minutes before attempting to remove the handle again.

2. It’s a good idea to keep track of any screws, caps, or retaining nuts that are removed so they can be easily reinstalled later.

3. If the faucet is old or has been in place for a long time, it may be rusted or corroded, making it more difficult to remove. In such cases, using a penetrating oil or rust dissolver can help loosen the parts. Follow the manufacturer’s instructions for the proper use of these products.

Conclusion

Removing an American Standard kitchen faucet may seem like a complicated task, but with these simple steps and the right tools, anyone can do it. Once you’ve removed the old faucet and installed the new one, you’ll enjoy a leak-free faucet that will provide you with years of trouble-free use.

Remember to always turn off the water supply before working on your plumbing, and if you’re unsure about any aspect of the removal process, consult a professional plumber to avoid any mishaps.

FAQs

What is a rubber washer and why is it important?

A rubber washer is a small piece of rubber that is used to create a seal between the faucet and the sink. It helps to prevent leaks and ensure proper water flow.

Can I use replacement parts from a different brand than my American Standard faucet?

It’s not recommended, as replacement parts are designed specifically for each faucet model. Using parts from a different brand can cause leaks, flow problems, or even damage to your plumbing.

How do I know what replacement faucet to buy?

Look for the model number of your American Standard faucet, which is usually located on the back of the faucet base or handle. You can then search for the exact match replacement faucet based on the model number.

Is it necessary to hire a plumber to replace a kitchen faucet?

No, it’s a relatively easy task that most people can do themselves with the right tools and knowledge.

How often should I perform maintenance on my kitchen faucet?

It’s a good idea to perform maintenance on your kitchen faucet once a year to ensure proper flow and prevent leaks. This includes cleaning the aerator, checking hoses for clogs, and tightening any loose screws.